helical angle
英 [ˈhelɪkl ˈæŋɡl]
美 [ˈhelɪkl ˈæŋɡl]
网络 螺旋角
双语例句
- Carbide welded side and face milling cutter helical rake angle
硬质合金焊接式三面刃铣刀（铣刀的）轴向刀面角 - Standpipes are big water tanks. Theoretical Analysis of Chip Flute of Spiral Taper Milling Cutter with An Equal Helical Angle
等螺旋角锥形立铣刀容屑槽槽形的理论分析 - Helical gear with helix angle
带螺旋角的螺旋齿轮 - Characteristics and helical angle of circular arc gear pair for drilling equipment transmission
钻采设备用双圆弧齿轮传动啮合特性分析与螺旋角设计 - Useless and Old Gear Helical Angle Measurement with Hobbing Machine
用滚齿机测量废旧齿轮的螺旋角 - An investigation on the ranges of helical lead angle of blade roller of fleshing machine
去肉机刀辊螺旋角大小的研究去肉机刀轴挠度计算的理论探讨 - Three Axes Numerical Control Machining of Tape Mill Cutter with Equal Helical Angle and Controllable Rake Angle
前角可控的等螺旋角锥形铣刀三轴数控加工原理 - The initial helical winding angle and the laminated thickness were considered as design variables, while the minimum structural mass as the objective function.
以螺旋向铺层的初始缠绕角和厚度为变量，对结构进行重量最小化设计。 - Universal algorithm for grinding rake face and clearance face of milling cutters with equal helical angle edge
一次走刀磨削等螺旋角铣刀前后刀面的通用算法 - Universal algorithm for revolving cutters with equal helical angle edge
等螺旋角回转刀具刀刃曲线的通用算法 - Based on theoretic analysis and practical experience, this paper not only systematically describes the advantages of big helical angle, wide pick spacing, low drum speed, reverse revolution and deep cutting, but also puts forward the reasonable range and fit relationship.
本文根据理论分析和现场实践效果，系统地阐述了大升角、宽截距、低转速、逆转向、深截割的优越性，指出了滚筒参数的合理取位范围和匹配关系。 - Microfibrillar helical angle of cell walls of cotton fiber and its relation to days post-anthesis
棉纤维细胞壁的微纤丝螺旋角及其与花后生长天数的关系 - Die Casting Die with Screw Arbor with Large Helical Angle for Screw Thread Unloading
大螺旋角螺杆脱螺纹压铸模 - The Influence of Plunger Diameter and Helical Angle of Injection Pump on Dynamic Process of Engine Speed Adjusting System
喷油泵柱塞直径及螺旋角对柴油机调速系统动态过程的影响 - Generalized Definition of Helical Angle and It's Applications
螺旋角的广义定义及其应用 - Herefrom, the influence of plunger diameter and helical angle on dynamic process of engine speed adjusting system is emphatically analysed by means of computer simulation.
在此基础上，用计算机仿真的方法，着重分析了喷油泵柱塞直径及螺旋角对柴油机调速过程的影响。 - In the light of this, the criteria for choosing the values of the normal pressure angle and helical angle of the gear ale laid down, and the equation for calculating the contact stress is simplified with coefficients and the corresponding coefficient graphs are presented.
为此，制定了齿轮法向压力角和螺旋角取值标准，并将击面接触应力公式系数化，最后给出筒化后的接触应力计算公式和相应的系数图表。 - Design and Calculating Method for Helical Coil Springs with Equal Helical Angle and Variable Diameter of Coils
等螺旋角圆锥压缩螺簧的计算方法 - Optimization of helical angle of tooth of oblique-toothed synchronous belt
斜齿同步带带齿螺旋角的优化设计 - At the same time the expressions of critical helical angle were worked out to helical gear pumps with backlash or not.
同时分别推导出了无齿侧侧隙斜齿轮泵和有齿侧侧隙斜齿轮泵的临界螺旋角表达式。 - A Discussion About the Definition of the Helical& angle of Finger Gear Cutter
指形铣刀螺旋角定义的探讨 - By employing the numeric analysis method, the influence of speed ratio, pressure angle, helical angle, gears positions, power, clearance ratio, and width to diameter ratio of bearing, on the response of the system is investigated.
用数值分析方法，研究了齿轮传动比、压力角、螺旋角、齿轮位置、功率、轴承间隙比与宽径比对系统不平衡响应的影响。 - The optimization model of sealing ability for a bushing helical seal is presented. In this model, the maximum value of sealing coefficient is objective function, and the relative groove depth, the relative groove width and helical angle are designed variables.
以密封系数最大为优化目标函数，考虑了相对槽深、相对槽宽和螺旋角等约束条件，建立了螺套式螺旋密封封液能力优化的数学模型。 - By controlling the offset distance EXF of the axis of outer cutter head to ensure the tooth thickness, avoiding the helical angle and curvature deviation generated by the existing algorithms.
通过控制外刀盘回转中心的偏距EXF保证了轮齿的齿厚，避免了现有算法产生的螺旋角偏差和曲率偏差。 - The number of balls in the ball screw mechanism is deduced correctly with concern of helical angle.
充分考虑螺旋升角因素，推导出了螺旋滚道内的滚珠数目。 - In this paper, through three-dimensional modeling software UG designed 11 programs intake port with different entrance shape, entrance height, spiral height and helical screw section angle.
本文通过三维建模软件UG设计了具有不同入口形状、入口高度、螺旋段高度和螺旋段夹角的11种螺旋进气道方案。 - The contact stress and deformation decrease with increasing of the contact angle. And the variation of helical angle has no noticeable influence on contact characteristic of ball screw mechanism. However, the contact characteristic is very sensitive to the variation of the curvature ratio.
随着接触角的增大，接触压力和变形减小，螺旋升角对接触特性无显著影响，接触特性对曲率比的变化非常敏感，随着曲率比的增大，接触压力和变形显著上升。